Coolant troubles

for zoze who'd like to spik angliche...

Modérateur : Modérateurs

Répondre
Avatar du membre
bouncybili
maitrise les leviers "jaune et rouge"...
Messages : 21
Enregistré le : mardi 15 févr. 2011 10:57
Localisation : Mayenne

Coolant troubles

Message par bouncybili »

Hi

Series 3, 2.25 petrol. Temp gauge not working so connected wire straight to earth and gauge went straight to the top so I've replaced the sender.

Now, 2 issues:
1 - I drained the coolant from the radiator only and not from the block drain. When I refilled (slowly) using the coolant I'd removed (which was still nice and clean and fresh antifreeze), I couldn't fit it all back in. What's going on???

2 - temp gauge reads even colder than before - it's off the bottom of the scale. Brand new sender.

Help???

Bil
1972 Séries III 88" dit "Pickle"
Avatar du membre
bouncybili
maitrise les leviers "jaune et rouge"...
Messages : 21
Enregistré le : mardi 15 févr. 2011 10:57
Localisation : Mayenne

Re: Coolant troubles

Message par bouncybili »

OK I've resolved the sender problem, it was the wrong part!!

Any ideas on the refilling of the system and possible airlocks gratefully received.
1972 Séries III 88" dit "Pickle"
Lodo
dort avec la 'green bible'...
Messages : 111
Enregistré le : vendredi 04 sept. 2015 21:14
Localisation : Port grimaud

Re: Coolant troubles

Message par Lodo »

Let it warm at idle whitout the radiator cap and wait for the termostat opening, and after refill whith coolant.
Avatar du membre
bouncybili
maitrise les leviers "jaune et rouge"...
Messages : 21
Enregistré le : mardi 15 févr. 2011 10:57
Localisation : Mayenne

Re: Coolant troubles

Message par bouncybili »

Thanks :)

Got to get it going as got the CT on Friday!!
1972 Séries III 88" dit "Pickle"
Avatar du membre
bouncybili
maitrise les leviers "jaune et rouge"...
Messages : 21
Enregistré le : mardi 15 févr. 2011 10:57
Localisation : Mayenne

Re: Coolant troubles

Message par bouncybili »

This is getting worse!!!

Just drained it again and flushed through with clean water and let it all drain. Could only get 8 litres and I got about 10 out! Ran engine with rad cap off and it soon started to rise up and overflow. Infra red temp reader on the thermostat housing read about 65 C. All hoses were hot and if I increased the revs the coolant went down in the rad but then came up again very frothy and overflowed again when I lowered the revs. I couldn't seem to get it hot enough to open the thermostat.

Stumped now!
1972 Séries III 88" dit "Pickle"
Avatar du membre
viking01
songe à monter un 'schnorkel'...
Messages : 492
Enregistré le : mercredi 31 oct. 2012 10:28
Localisation : Pays de Gex, 01

Re: Coolant troubles

Message par viking01 »

Hello

I had similar issues when I reassembled my diesel after refurb, your thermostat might be stuck, I went through three units before I had a functional system. If you change it make sure to stay away from the britparts ones.....

~Johan
Avatar du membre
bouncybili
maitrise les leviers "jaune et rouge"...
Messages : 21
Enregistré le : mardi 15 févr. 2011 10:57
Localisation : Mayenne

Re: Coolant troubles

Message par bouncybili »

viking01 a écrit :Hello

I had similar issues when I reassembled my diesel after refurb, your thermostat might be stuck, I went through three units before I had a functional system. If you change it make sure to stay away from the britparts ones.....

~Johan
Thanks, I'm seriously suspecting the thermostat too.
1972 Séries III 88" dit "Pickle"
Lodo
dort avec la 'green bible'...
Messages : 111
Enregistré le : vendredi 04 sept. 2015 21:14
Localisation : Port grimaud

Re: Coolant troubles

Message par Lodo »

Don't forget to drill a 3mm hole in the thermostat to let the water flow pass trough when it is close.
Avatar du membre
bouncybili
maitrise les leviers "jaune et rouge"...
Messages : 21
Enregistré le : mardi 15 févr. 2011 10:57
Localisation : Mayenne

Re: Coolant troubles

Message par bouncybili »

Lodo a écrit :Don't forget to drill a 3mm hole in the thermostat to let the water flow pass trough when it is close.
Why would I want to do that?
1972 Séries III 88" dit "Pickle"
Lodo
dort avec la 'green bible'...
Messages : 111
Enregistré le : vendredi 04 sept. 2015 21:14
Localisation : Port grimaud

Re: Coolant troubles

Message par Lodo »

bouncybili a écrit :
Lodo a écrit :Don't forget to drill a 3mm hole in the thermostat to let the water flow pass trough when it is close.
Why would I want to do that?
To let the air bubles goes out when it's close before the engine warm and the thermostat start to open. The hole must be one the edge of the thermostat. Sometimes some thermostats are sale whith the ole predrilled.
Répondre